Uniden BC125XLT: ARC125 V0.97 build 2 for Uniden BC125AT. Uniden BC75XLT: ARC75 V0.9 build 1 for Uniden BC75XLT. ARC536 PRO for Uniden BCD436HP and BCD536HP. ARC536 BASIC for Uniden BCD436HP and BCD536HP. Hi Fred i have never used freescan arc xt pro has always done the job.i have never had this problem before with arc xt.i did a search for the latest version of freescan the other day and i could not find version 2.18 which is the version needed to work with the p 2. Scanner Software Download, select your scanner model: Portable scanners. It’s been a while, but as I recall to use FreeScan with the BCD996P2 or the BCD325P2 it is necessary to use the beta6 version. I use FreeScan 2.18-beta6 to program all of the scanners without any problems. I’m sure you have, but to be sure did you downloadįreeScan 2.18-beta6? I have a BCD996XT, 2 BCD996P2’s, a BCD396XT, BC346XT, and BC246T. baconbuccaneer New York Radio Discussion Forum Replies 7 Views 740. This email has been checked for viruses by Avast antivirus software. With ARC-XT Pro and RadioReference helping, programmed several law, fire, and EMS groups within the GATRRS system and Sim 1 site along with a few VHF freqs. Will work with the p2.again many thanks to all i am just too frustrated ARC-XT has been updated to handle the BCD996P2 but make sure that you have the latest version (2.x). Butel XT pro software was a pain trying to install on an 8.1 machine but. Hello group i thank everyone for replying to me,right now i am toįrustrated to work with it.Joe i have not found a version freescan that made for Uniden.The BCD996P2 has a 9-pin RS-232 serial port connector on the rear panel. They are not special cables from Uniden, just generic.įar as drivers with windows 10 it will load the correct ones. If this doesn't work, replace the cable, they do go bad, I replaced one. One easy test is, can you control the radio with freescan? If you can,įreescan- Scanner, control scanner, then click "com port setup." thenĬlick "Start Auto", then click "Start virtual control" Normally I click the "All" box, then click "start upload" Of course then put check marks to the left of the systems you want to "Upload programming" popup box, then click the box to the left of "Start Now DEC-9104 HEX-2390 is BPD 4A NE4A Northeastern District and once again 853.8750 DAT shows up and hangs with NO SOUND. Item is once the cable is hooked up, what always MUST be done is at the ARC XT is THE preferred and best selling programming software for the Uniden XT series, ARC-XT-PRO adds powerful data logging, digital audio recording and a fantastic bandscope Main features: - ARC-XT supports the following scanner models: BCD396XT, BC346XT, BCD996XT and BCT15X. Ok, so now ive reset the scanner to factory settings, Firmware is up to date, downloaded ARC-XT. The Scanner"s Firmware has to be updated from 1.05.02 to 1.07.06 for the Upgrade to work or the Key Code will not work.I have programmed 100's of scanners most not mine with freescan, the KEY There is no "Upgrade" or "Upgrade DMR" on the Menu selections. I was told to go to: Menu, then Settings, then Upgrade, then Upgrade DMR. I have been emailing with Uniden Tech Support as well and asking them questions. I did purchased the ARC-XT Pro Software recently. The BCD996P2 is the sister scanner to the BCD325P2 and should have the same menu selections. As noted, enter ALL of the key, including the dashes. But presuming it's menu is similar to it's hand-held sibling, the 325P2, access the menu, then select Settings, then select Upgrade to get to the point where you can enter the Upgrade Key. ![]() Since you are going to be using DMR, the only two software packages that will do that for your BCD996P2 are ARC-XT & ProScan. ![]() The other version is for the 436HP & 536HP. Depending on which of the two versions you downloaded, one version of Sentinel is for the Home Patrol-1 & -2. Sentinel software will not do anything for your 996P2.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |